The variation in crown-root morphology of anterior teeth assessed with cone-beam computed tomography

ABSTRACT Objective: To determine the discrepancy of crown-root morphology of anterior teeth, using cone-beam computed tomography (CBCT), and to provide a guidance for proper torque expression. Methods: A total of eligible 200 CBCT were imported into Invivo v. 5.4 software, to obtain the middle labio-lingual sections of anterior teeth. AutoCAD 2007 software was applied to measure the crown-root angulation (Collum angle) and the angle formed by a tangent to the center of the labial surface and the long axis of the crown (labial surface angle). SPSS 18.0 was used for statistical comparisons of the two measurements, at the level of p< 0.05, and the Pearson correlation analysis was applied to investigate the association between the two measurements. Results: The value of Collum angle in maxillary central incisor was close to 0°. Significantly negative Collum angle in lateral incisors and maxillary canine, and positive value in mandibular canine were detected (p < 0.001). The labial surface angle in canine was significantly greater than the intra-arch incisors (p< 0.001), and no significant difference was detected between the central and lateral incisors (p > 0.05). Notably, there was also a significant positive correlation between the two measurements. Conclusions: The crown-root angulations were greatly different among anterior teeth. Accompanying the obvious crown-root angulations, the canines both in maxillary and mandibular arches presented considerable labial surface curvatures. Hence, equivalent deviation during bracket bonding might cause greater torque expression error and increase the risk of alveolar fenestration and dehiscence.

RESUMO Objetivo: Determinar a discrepância na morfologia coroa-raiz de dentes anteriores, utilizando tomografia computadorizada de feixe cônico (TCFC), e fornecer parâmetros para a expressão apropriada do torque. Método: No total, 200 tomografias elegíveis foram importadas para o software Invivo 5.4 para obtenção das secções médias vestibulolinguais dos dentes anteriores. Osoftware AutoCAD 2007 foi usado para medir a angulação coroa-raiz (ângulo Collum) e o ângulo formado por uma tangente ao centro da superfície vestibular da coroa e o longo eixo da coroa (ângulo da superfície vestibular). O software SPSS 18.0 foi utilizado para as comparações estatísticas das duas medições, com nível de significância de p< 0,05, e a análise de correlação de Pearson foi aplicada para investigar a associação entre as duas medições. Resultados: O valor do ângulo Collum do incisivo central superior foi próximo a 0°. Foram detectados valores significativamente negativos para o ângulo Collum nos incisivos laterais e caninos superiores, mas valores positivos nos caninos inferiores (p< 0,001). O ângulo da superfície vestibular no canino foi significativamente maior do que nos incisivos intra-arcada (p< 0,001), e nenhuma diferença significativa foi detectada entre incisivos centrais e laterais (p> 0,05). Também foi observada uma correlação positiva significativa entre as duas medições. Conclusões: As angulações coroa-raiz foram muito diferentes entre os dentes anteriores. Os caninos superiores e inferiores apresentaram considerável curvatura na superfície vestibular, associada a uma evidente angulação coroa-raiz. Consequentemente, desvios durante a colagem de braquetes podem desencadear maior erro na expressão de torque e aumentar o risco de fenestração alveolar e deiscência, sendo necessária uma avaliação antes da colagem.

Endothelial nitric oxide synthase gene polymorphisms associated with susceptibility to high altitude pulmonary edema in Chinese railway construction workers at Qinghai-Tibet over 4 500 meters above sea level / 中国医学科学杂志(英文版)

<p><b>OBJECTIVE</b>To examine whether the polymorphisms of endothelial nitric oxide synthase (eNOS) gene are associated with the susceptibility to high altitude pulmonary edema (HAPE) in Chinese railway construction workers at Qinghai-Tibet where the altitude is over 4 500 m above sea level.</p><p><b>METHODS</b>A case-control study was conducted including 149 HAPE patients in the construction workers and 160 healthy controls randomly recruited from their co-workers, matching the patients in ethnicity, age, sex, lifestyle, and working conditions. Three polymorphisms of eNOS gene, T-786C in promoter, 894G/T in exon 7, and 27bp variable number tandem repeat (VNTR) in intron 4, were genotyped using polymerase chain reaction (PCR) and confirmed with DNA sequencing.</p><p><b>RESULTS</b>The frequencies of 894T allele and heterozygous G/T of the 894G/T variant were significantly higher in HAPE patients group than in the control group (P=0.0028 and P=0.0047, respectively). However, the frequencies of the T-786C in promoter and the 27bp VNTR in intron 4 were not significantly different between the two groups. Haplotypic analysis revealed that the frequencies of two haplotypes (H3,T-T-b, b indicates 5 repeats of 27 bp VNTR; H6, C-G-a, a indicates 4 repeats of 27 bp VNTR) were significantly higher in HAPE patients (both Pü0.0001). On the contrary, the frequencies of H1 (T-G-b) and H2 (T-G-a) were lower in HAPE patients than in healthy controls (both Pü0.001).</p><p><b>CONCLUSIONS</b>Two haplotypes (T-T-b and C-G-a) may be strongly associated with susceptibility to HAPE. Compared with the individual alleles of eNOS gene, the interaction of multiple genetic markers within a haplotype may be a major determinant for the susceptibility to HAPE.</p>